Magnetic Measuring Systems GN 7110 (MPI-R10)

GN 7110 Magnetic Measuring Systems for Length and Angle Measurements

Original design
code: MPI-R10 / MPI-R10-RF

Standard sheet GN 7110 Print this page IP Protection Classes Plastic Characteristics Operation Instruction GN 7110

Product description

Magnetic measuring systems GN 7110 and magnetic bands GN 7110.2 together form a complete system for length and angle measurement. They are suitable for applications requiring frequent adjustments, such as at cutting and trimming stations.

Together with control units GN 9150, the V2 version forms a wireless system for fast positioning. Due to the wireless transmission, no cable is required between the control unit and the measuring system. Format changes can be quickly transmitted from a control station.

Specification

Housing
Plastic, Polyamid (PA)

Glass fiber reinforced
Operating temperature 0 °C to +50 °C
Black, matte finish

Retaining clip
Plastic, Polyacetal (POM)
Black, matte finish

LCD display
Plastic, Polycarbonate (PC)

Sensor
Zinc die casting, nickel-plated

Cable (Outer sheath)
PVC

Plug
Plastic, Polyamid (PA)

Glass fiber reinforced
Black
O-ring
Acrylonitrile butadiene rubber (NBR)

RoHS

Accessory

Magnetic Bands GN 7110.2
Control Units GN 9150

GN 7110 Magnetic Measuring Systems for Length and Angle Measurements sketch

Hide technical drawing

Article options / Table

Identification no.

1	Protection class IP 54
2	Protection class IP 67

Coding

E	No wireless data transmission
V2	With wireless data transmission, version 2

Show / Hide columns

l₆ in meters (cable length)							l₁	l₂	l₃	l₄	l₅	h₁	h₂	h₃

0,2	0,3	0,5	0,8	1,2	2	2,5	72	12	28	21	7	37	20,5	16,5

Build & Price

Electrical and Mechanical Properties

Tension feed

Lithium battery 1/2 AA 3,6 V

Battery life

2.5 years

Display

7-digit LCD display,
12 mm high with special character support

Reading scale

-199999; 999999

Number of decimal digits

programmable (see operating instruction)

Units of measure

mm, inch or degrees (programmable)

Max operating speed

1 ... 5 m/s programmable (reading speed affects battery life)

Resolution

0.01 mm / 0.001 in / 0,01°

Precision

± 0.03 mm

Repeatability

0.0002 x L mm (L = value measured in mm)

Self-diagnostic

Battery check, sensor check, magnetic tape check

Reverse voltage protection

Yes

Operating temperature

0 °C ... 50 °C

Operating environment

Internal use

Relative humidity

Max. 95% at 25°C (without condensation)

Frequency range
(Version 2)

2,4 GHz ... 2,416 GHz

Compatibility

Magnetic measuring systems and control units
can only be combined with each other in the same version.

Configurable Display Options

One advantage of using an electronic positioning device lies in the wide range of display options of the magnetic measuring system.
The following settings can be configured with 4 multifunction keys:

Selecting incremental or absolute measuring mode
Changing the unit of measurement (mm, inch or degrees)
Resetting the counter or setting an offset value
Storage and display of 32 target positions

The lithium battery is included and has a service life of up to 2.5 years. A display symbol indicates when the battery needs to be replaced. The battery can be easily replaced by removing the rear cover. If the battery is replaced within 10 seconds, the buffer power supply prevents the loss of the configured parameters.

Other important information and notes can also be found in the operating instruction. It is part of the scope of delivery and can be downloaded as a PDF at ganternorm.com/service/downloads/operating-instructions.

Assembly Instruction

Please use the dimensions as per the table for the cutout in the housing.
Deburr the cutout before inserting the display.
At first, insert the display at the bottom of the opening.
Then press in the upper part until it snaps completely into place.

Show / Hide columns

Wall thicknes s	x +0,2	y -0,5

> 0.7 ... 2	67	34

Battery Replacement Instructions

Take out the unit by pressing down on the retaining clip at the top of the housing using a slotted screwdriver.
Remove the screw on the back side of the housing, and take off the cover.
Replace the battery, taking care to match the polarity correctly (see the position indicated on the cover). If the battery is replaced within 5 seconds, the buffer power supply prevents the loss of the configured parameters.

Application Example

To ensure an accurate measurement, the distance between the sensor and the magnetic band should not exceed 1 mm. The sensor can be mounted using M3 screws.

Selected Part (How to order)

Part number

Total (net)

265,31 €

plus VAT 50,41 €
gross 315,72 €

In stock

Weight: 0,172 kg

If this article is new in our product range, it may happen that details concerning weight are as yet not listed.
If you do need weight details, please contact our Sales Department!
Phone +49 7723 6507 - 0

RoHS: Yes

This article is RoHS-compliant in application of Annex III., which means it complies with EU Directive 2011/65/EU, including extension (2015/863/EU), for restricting the use of certain hazardous substances in electrical and electronic devices. The Directive regulates the use of hazardous substances in devices and components. The implementation in national law is summarily described with RoHS(Restriction of (the use of certain) hazardous substances).

Customs tariff number

90318080

Please note our order discounts.

With a total value (net) per order:
from 175,00 € -> 10 % discount
from 275,00 € -> 20 % discount
from 375,00 € -> 30 % discount

Surcharge for small volume purchases:
-> 15,00 Euro
for value of goods less than 25,00 €
-> 10,00 Euro
for value of goods from 25,00 to 49,99 €

Quantity

All prices in accordance with our price list No. 56, valid from 1 September 2024, plus VAT only valid for Germany.